admin 24 February, 2019 0

ASTM D3171 PDF

Intertek tests composite materials constituent content, using ASTM D Content analysis for composite materials ASTM D scope: The test method ASTM. Intertek tests composite materials constituent content, using ASTM D Content analysis for composite materials ASTM D scope: The test method. To extend the burn off test protocol in ASTM D to the determination of The current ASTM test method incorporates resin burn off as a way to determine.

Author: Goltikazahn Nikohn
Country: Jordan
Language: English (Spanish)
Genre: Politics
Published (Last): 13 September 2016
Pages: 253
PDF File Size: 9.1 Mb
ePub File Size: 5.53 Mb
ISBN: 954-1-62282-173-5
Downloads: 50432
Price: Free* [*Free Regsitration Required]
Uploader: Faelkis

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine atm applicability of regulatory limitations prior to use.

No other units of measurement are included in this standard. From the specimen density, constituent densities, and the fiber content, the reinforcement content, matrix content, and void content can then be determined. Test Method II, applicable only v3171 laminate materials of known fiber areal weight, calculates reinforcement or matrix content by weight or volumeand the cured ply thickness, based on the measured thickness of the laminate.

Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace. Test Method I physically removes the matrix by digestion or ignition by one of seven procedures, leaving the reinforcement essentially unaffected and thus allowing calculation of reinforcement or matrix content by weight or volume as well as percent void volume.

Work Item s – proposed revisions of this standard. Assurance Testing Inspection Certification.

Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social c3171 standards for virtually any market around the world.

  INTRODUCTION TO GOVERNMENT AND BINDING THEORY HAEGEMAN PDF

Eq 9 and 10 assume zero void content to perform the calculation. Method I removes the matrix by digestion or ignition. Auditing Consulting Sourcing Training.

ASTM D – 15 Standard Test Methods for Constituent Content of Composite Materials

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior asrm use. Link to Active This link will always route to the current Active version of the standard.

The suggested applications are discussed in Section 4as well as at the start of each procedure. See Section 9 for additional information. Validating the specifications, value and safety of your raw materials, products and assets. Send us a request Wilton UK: Enabling you to identify and mitigate the intrinsic risk in your ast, supply chains and business processes.

ASTM D – 99 Standard Test Methods for Constituent Content of Composite Materials

Inspection Validating the specifications, value aetm safety of your raw materials, products and assets. Also, knowledge of the constituent content is required for evaluation of the quality of a fabricated material and the processes used during fabrication.

Need help or have a question? The presence of voids is not measured.

Content Analysis for Composite Materials by ASTM D3171

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.

However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can be determined in every case.

  BEATRIZ SARLO LA PASION Y LA EXCEPCION PDF

Higher void volumes usually mean lower fatigue resistance, greater susceptibility to moisture penetration and weathering, and increased variation or scatter in strength properties. The resulting solution is then filtered and the amount of remaining fiber is determined. Formally confirming that your products and services meet all trusted external and internal standards.

Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. Active view current version of standard. For method I, three specimens are machined from customer supplied product. Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace.

However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can be determined in every case.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The suggested applications are discussed in Section 4, as well as at the start of each procedure. Procedure H carbonizes the x3171 in a furnace.

Historical Version s – view previous versions of standard.

Eq 15 and 16 assume zero void content to perform the calculation.